FME2404R
Find Parts for FME2404R
Browse OEM replacement parts for the FME2404R ice machine and use the parts diagram below to identify the correct component before ordering.
View Parts Diagram for
FME2404R
Looking to buy a new ice machine
to replace this model?
Request a Quote →
Parts associated with FME2404R
- 02-0836-00 — Catch
- 02-0929-23 — Water Seal
- 02-1338-00 — Hose clamp
- 02-2916-01 — Slotted Collar
- 02-2926-01 — Ice Chute Body 21. 13-0617-54 O-Ring
- 02-2929-04 — Ice Chute Lower 24. 03-1544-08 Soc. Head Screw
- 02-2930-04 — Ice Chute Cover 19. 02-2977-01 Lip Seal
- 02-2977-01 — Lip Seal
- 02-2978-01 — Lip Seal
- 02-3001-01 — Ice Sweep 28. 03-1420-03 Cap Screw
- 02-3128-20 — Breaker Cover
- 02-3266-01 — Reservoir & valve
- 02-3266-02 — Float valve
- 02-3266-03 — Plunger/seat 02-3826-02 Res. overflow hose (left)
- 02-3268-01 — Drain tube holder 18. A34559-020 Bearing
- 02-3319-02 — Dryer
- 02-3575-01 — Fan guard
- 02-3692-22 — Drain fitting
- 02-3826-01 — Res. overflow hose (right)
- 02-3826-02 — Res. overflow hose (left)
- 02-3837-01 — Drip Pan
- 02-4358-01 — Insulation
- 02-4663-01 — Water Shed
- 03-0271-00 — Speed Clip
- 03-1394-01 — Pal Nut
- 03-1404-12 — Screw
- 03-1405-20 — Cap Screw
- 03-1405-27 — Screw
- 03-1405-41 — Cap Screw
- 03-1405-52 — Hex Cap Screw 27. A32890-020 Evaporator
- 03-1406-13 — Nut
- 03-1407-07 — Washer
- 03-1408-36 — Washer
- 03-1419-22 — Screw
- 03-1420-03 — Cap Screw
- 03-1531-01 — Screw
- 03-1544-08 — Soc. Head Screw
- 03-1638-03 — Screw
- 03-1645-01 — Screw
- 08-0660-01 — Auger Stud & washer
- 11-0422-25 — Discharge pressure control
- 11-0488-21 — Thermo Expansion Valve
- 11-0501-22 — Hi Pressure Cut Out
- 11-0502-21 — Low pressure cut out
- 12-0426-02 — Mode Switch
- 12-1576-02 — Fan Motor
- 12-1868-03 — Crankcase heater - RS comp
- 12-2070-04 — Fan Motor Relay
- 12-2135-02 — Liquid line valve
- 12-2350-01 — Spacer/screw
- 12-2430-22 — Drive Motor-230v
- 12-2430-24 — Start switch, Emerson
- 12-2430-29 — Rotor Bearing, Emerson
- 12-2430-44 — Start switch, GE split phase
- 12-2430-49 — Rotor bearing, GE split phase
- 12-2469-02 — Single Phase Contactor
- 12-2533-02 — Three Phase Contactor
- 12-2760-21 — Water Level Sensor
- 12-2835-22 — Circuit Board
- 12-3043-02 — Crankcase heater - RST comp
- 13-0617-45 — O-Ring
- 13-0617-49 — O-Ring
- 13-0617-52 — O-Ring
- 13-0617-54 — O-Ring
- 13-0704-00 — Gasket
- 13-0840-01 — Rubber cap
- 13-0871-01 — Water Shed 29. 02-4358-01 Insulation
- 13-0895-01 — Inlet tubing
- 15-0808-01 — Emblem, gray
- 16-0761-01 — Receiver
- 16-0778-21 — Accumulator
- 16-0832-02 — Stem cap 26. 16-0778-21 Accumulator
- 16-0832-03 — Core cap 27. 11-0502-21 Low pressure cut out
- 16-0832-20 — Access valve
- 16-0835-01 — Inlet fitting for plastic tubing
- 16-0850-01 — Liquid line fitting
- 16-0850-03 — Discharge line fitting
- 16-1039-01 — Male connector for plastic
- 16-1057-01 — Line connection, female half 3/8'
- 16-1057-02 — Line connection, female half 1/2'
- 16-1137-01 — Access valve body
- 16-1139-01 — Core
- 16-1140-01 — Cap
- 17-3016-01 — V RELAY SWITCH
- 17-3018-01 — SOLENOID SOL GN
- 18-1901-20 — Start Capacitor
- 18-1901-53 — Start capacitor
- 18-1901-54 — Start Capacitor
- 18-1902-45 — Run Capacitor
- 18-1902-53 — Run capacitor
- 18-1902-67 — Run Capacitor
- 18-1903-29 — Potential relay
- 18-1903-33 — Potential Relay
- 18-1903-54 — Potential Relay
- 18-2200-27 — Sleeve
- 18-2200-28 — Grommet
- 18-8708-01 — Fan Blade
- 18-8768-22 — Compressor 208-230/60/1
- 18-8768-24 — Compressor 208-230/60/3
- 18-8772-21 — Overload
- 18-8772-26 — Compressor 230/50/1
- 18-8796-32 — Fan motor
- 18-8800-01 — Fan blade
- 18-8955-22 — Compressor 208-230/60/1
- 18-8955-23 — Compressor 208-230/60/3
- 18-8955-53 — Overload
Shop FME2404R Parts
About FME2404R Ice Machine Parts
We carry OEM parts for the FME2404R ice machine to help you repair, maintain, and extend the life of your equipment. Use the parts breakdown PDF above to identify the correct component and match it to the products listed on this page.
Popular replacement items may include pumps, valves, sensors, motors, and control components, depending on the machine configuration. Ordering the correct OEM part helps reduce downtime and improves long-term reliability.