NME1850R

Parts associated with NME1850R

• 02-0836-00 — Catch
• 02-0929-23 — Water Seal
• 02-1338-00 — Hose clamp
• 02-2618-01 — Fan Guard
• 02-2916-01 — Slotted Collar
• 02-2926-01 — Ice Chute Body 21. 13-0617-54 O-Ring
• 02-2929-04 — Ice Chute Lower 24. 03-1544-08 Soc. Head Screw
• 02-2930-04 — Ice Chute Cover 19. 02-2977-01 Lip Seal
• 02-2977-01 — Lip Seal
• 02-2978-01 — Lip Seal
• 02-3001-01 — Ice Sweep 28. 03-1405-41 Cap Screw
• 02-3128-20 — Breaker Cover
• 02-3266-01 — Reservoir & valve
• 02-3266-02 — Float valve
• 02-3266-03 — Plunger/seat
• 02-3268-01 — Drain tube holder 18. A34559-020 Bearing
• 02-3319-02 — Dryer
• 02-3575-01 — Fan guard
• 02-3692-22 — Drain fitting
• 02-3837-01 — Drip Pan
• 02-4663-01 — Water Shed
• 03-0255-04 — Wing Nut 13. 12-2340-01
• 03-0271-00 — Speed Clip
• 03-1394-01 — Pal Nut
• 03-1404-12 — Screw
• 03-1405-20 — Cap Screw
• 03-1405-27 — Screw
• 03-1405-41 — Cap Screw
• 03-1405-52 — Hex Cap Screw 27. A32890-020 Evaporator
• 03-1406-13 — Nut
• 03-1407-07 — Washer 26. 16-0778-21 Accumulator
• 03-1408-36 — Washer
• 03-1417-15 — Lockwasher 11. 12-2285-22 Transformer
• 03-1419-22 — Screw 16. A36554-001 Base
• 03-1531-01 — Screw
• 03-1544-08 — Soc. Head Screw
• 03-1638-03 — Screw (Transformer to Circuit Board)
• 03-1638-04 — Screw
• 03-1639-03 — Screw
• 03-1645-01 — Screw Overload is internal
• 03-1652-02 — Bolt NOT ILLUSTRATED
• 08-0660-01 — Auger Stud & washer
• 11-0420-24 — Pump down control
• 11-0422-25 — Discharge pressure control
• 11-0485-21 — Hi Pressure Cut Out 18-8768-24 Compressor 200-230/60/3
• 11-0488-21 — Thermo Expansion Valve
• 12-0426-01 — Master Switch
• 12-0739-02 — Three Phase Contactor 15. 12-2070-04 Fan Motor Relay
• 12-1576-02 — Fan Motor
• 12-1868-03 — Crankcase heater
• 12-2070-04 — Fan Motor Relay
• 12-2135-02 — Liquid line valve
• 12-2285-22 — Transformer
• 12-2350-01 — Spacer/screw
• 12-2430-22 — Drive Motor-230v
• 12-2430-24 — Start switch, Emerson
• 12-2430-29 — Rotor Bearing, Emerson
• 12-2430-44 — Start switch, GE split phase
• 12-2430-49 — Bearing, GE split phase
• 12-2469-02 — Single Phase Contactor Separate From The Control Box
• 13-0079-03 — Res. overflow hose
• 13-0617-45 — O-Ring
• 13-0617-49 — O-Ring
• 13-0617-52 — O-Ring
• 13-0617-54 — O-Ring
• 13-0704-00 — Gasket
• 13-0840-01 — Rubber cap
• 13-0868-01 — Water Shed
• 13-0871-01 — Water Shed 29. A32962-001 Insulation Bot. (half)
• 15-0711-01 — Emblem, sandalwood
• 15-0808-01 — Emblem, gray A36517-002 Rear panel, SS
• 16-0162-00 — Strainer - not used after 11/97
• 16-0670-02 — Tee
• 16-0761-01 — Receiver
• 16-0778-21 — Accumulator
• 16-0791-01 — Coupling union
• 16-0832-02 — Stem cap
• 16-0832-03 — Core cap Overload is internal
• 16-0832-20 — Access valve
• 16-0835-01 — Inlet fitting for plastic tubing
• 16-0850-01 — Liquid line fitting
• 16-0850-03 — Discharge line fitting
• 16-1039-01 — Male connector for plastic
• 16-1057-01 — Line connection, female half 3/8'
• 16-1057-02 — Line connection, female half 1/2'
• 18-1901-54 — Start Capacitor
• 18-1902-45 — Run Capacitor
• 18-1903-33 — Potential Relay
• 18-2200-27 — Sleeve dryer & single phase include starting components
• 18-2200-28 — Grommet Note: Replacement compressors include a new HFC
• 18-2200-38 — Start Capacitor Cap. 8. 12-0426-01 Master Switch
• 18-2200-39 — Start Capacitor Bracket 9. 11-0420-24 Pump down control
• 18-5301-01 — Fan Motor
• 18-6304-01 — Fan Blade
• 18-8708-01 — Fan Blade
• 18-8768-22 — Compressor 208-230/60/1
• 18-8768-24 — Compressor 200-230/60/3
• 18-8796-32 — Fan motor
• 18-8800-01 — Fan blade