NME954R

View Parts Breakdown

Looking to buy a new ice machine

to replace this model? Request a Quote →

Parts associated with NME954R

02-0836-00 — Catch
02-0929-23 — Water Seal
02-1338-00 — Hose clamp
02-2916-01 — Slotted Collar
02-2929-04 — Ice Chute Lower
02-2930-04 — Ice Chute Cover
02-2977-01 — Lip Seal
02-2978-01 — Lip Seal
02-3001-01 — Ice Sweep
02-3128-20 — Breaker Cover
02-3266-01 — Reservoir & valve
02-3266-02 — Float valve
02-3266-03 — Plunger/seat
02-3268-01 — Drain tube holder
02-3319-02 — Dryer
02-3559-01 — is a needle that snaps onto a standard grease gun fitting. Use it to insert and deeply
02-3575-01 — Fan guard
02-3692-22 — Drain fitting
02-3826-01 — Res. overflow hose
02-3837-01 — Drip Pan
02-3841-01 — Ice Chute Body*
02-4358-01 — Insulation
02-4663-01 — Water Shed
03-0271-00 — Speed Clip
03-1394-01 — Pal nut
03-1404-12 — Screw
03-1405-20 — Cap Screw
03-1405-21 — Cap Screw
03-1405-27 — Screw
03-1405-41 — Cap Screw
03-1405-52 — Hex Cap Screw
03-1406-13 — Nut (for rec. not shown)
03-1407-07 — Washer
03-1408-36 — Washer
03-1410-06 — Washer (for rec. not shown)
03-1419-22 — Screw
03-1531-01 — Screw
03-1544-08 — Soc. Head Screw
03-1638-03 — Screw
03-1645-01 — Cap Screw (for rec. not shown)
08-0660-01 — Auger Stud & washer
11-0422-25 — Head Pressure Valve
11-0488-21 — Thermo Expansion Valve
11-0501-22 — Hi Pressure Cut Out
11-0502-21 — Pump down control
12-0426-02 — Mode Switch
12-1576-02 — Fan motor when single phase.
12-1868-03 — Crankcase Heater
12-2135-02 — Liquid Line Valve
12-2350-01 — Spacer/screw
12-2430-22 — Drive Motor
12-2430-24 — Start swtich, Emerson
12-2430-29 — Rotor Bearing, Emerson
12-2430-44 — Start switch, GE split phase
12-2430-49 — Rotor bearing, GE split
12-2469-02 — Single Phase Contactor
12-2533-02 — Three Phase Contactor
12-2760-21 — Water Level Sensor
12-2835-22 — Circuit Board
13-0617-45 — O-Ring
13-0617-49 — O-Ring
13-0617-52 — O-Ring
13-0617-54 — O-Ring
13-0704-00 — Gasket
13-0840-01 — Rubber cap
13-0871-01 — Water Shed
13-0895-01 — Inlet tubing
13-0929-01 — Insulation donut*
13-0929-02 — Insulation donut*
15-0411-00 — Strike (on front panel)
15-0808-01 — Emblem, gray
16-0761-01 — Receiver
16-0778-21 — Accumulator
16-0832-02 — Stem cap
16-0832-03 — Core cap Note: Compressors include dryer and starting components
16-0832-20 — Access valve 18-8655-53 Overload for above
16-0835-01 — Water fitting
16-0850-01 — 1/2' Male half
16-0850-03 — 3/8' Male half
16-1039-01 — Male connector
16-1137-01 — Access valve body
16-1139-01 — Core
16-1140-01 — cap
17-2679-01 — HIGH
18-1901-20 — Start capacitor, RST70 8. 12-0426-02 Mode Switch
18-1901-54 — Start Capacitor, RS70
18-1902-45 — Run Capacitor, RS70
18-1902-67 — Rub capacitor, RST70 NOT ILLUSTRATED
18-1903-33 — Potential Relay, RS70
18-1903-54 — Potential Relay, RST70
18-2200-27 — Sleeve
18-2200-28 — Rubber Grommet
18-8655-53 — Overload for above
18-8708-01 — Fan blade 26. 16-0778-21 Accumulator
18-8796-32 — Fan motor
18-8800-01 — Fan blade
18-8955-22 — Compressor 208-230/60/1
18-8955-23 — Compressor 200-230/60/3